find the right

Electrical Component

Start Now

Shop by Sub Category

Rating

& up
& up
& up
& up

Back to Category

Plant & Agriculture

Beacon & Lightbar & Workshop Lighting

Automotive Cooling & HVAC Components

Oil Cooler

Vehicle Lining, Flooring & Racking

Match service intervals to the equipment manufacturer's recommendations. Typical intervals: engine oil filter — every oil change (250-500 hours for plant; 5,000-15,000 km for HGV). Engine air filter — annually or per filter restriction-indicator (whichever is sooner). Engine fuel filter — every 250-500 hours, or sooner if water-separator indicator triggers. Hydraulic filter — every 1,000-2,000 hours typical. Cab air filter — annually or 12-month intervals. Severe-duty service (dusty environments, water-contaminated fuel, heavy-load operation) shortens these intervals. Always check the equipment service schedule.

Quality aftermarket filters from specialist filter manufacturers (with proper filter-media specification, dimensional accuracy, and rated to the OEM filtration specification) match OEM filter performance and service life. Lower-cost generic-aftermarket filters may have inferior filter media (lower filtration efficiency, lower contamination capacity, shorter service life). For trade-and-fleet service, specialist-brand aftermarket filters are the practical choice. Identify the original filter's manufacturer where listed; typically the same manufacturer's aftermarket equivalent is the most reliable replacement at lower cost than OEM.

Fuel filters are critical for diesel engine protection. Match by: (1) OEM cross-reference part number — the most reliable; (2) filter dimensions — overall diameter, height, sealing-ring size, and thread size on the filter mounting; (3) filtration rating — the engine manufacturer specifies the maximum micron rating for the engine's fuel-injection system (typical 5-10 microns for modern common-rail; 10-30 microns for older mechanical injection). Wrong-rated filters cause injector damage and high-pressure-pump wear. The micron rating is on every fuel-filter product page.

Yes. Service-pack kits (combining engine oil filter, engine air filter, fuel filter, and hydraulic filter for a specific equipment service interval — sized to do one complete service from a single pack) are available across the plant-equipment range. Service packs are typically 10-20% cheaper than buying filters individually and ensure all the right filters are on the bench when starting the service. Match by the equipment make, model, and service interval. WhatsApp 07754288583 with the equipment details for service-pack availability.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Clear

Filters

View as

Within Plant & Agriculture, Filters covers the engine, hydraulic, and equipment-system filters fitted to plant equipment, agricultural tractors, telehandlers, commercial vehicles, and the wider plant-and-vehicle filtration aftermarket — covering engine air filters (intake-air filtration, in panel and round-canister formats), engine oil filters (in spin-on, cartridge, and centrifugal-bypass formats), fuel filters (primary water-separator and secondary fine-fuel filters for diesel engines; in-line and cartridge formats), hydraulic filters (return-line, pressure-line, and suction-line filters for hydraulic-circuit cleanliness), cab air filters (for operator-cab HVAC systems — particle and activated-carbon filtration), and the matching filter housings, sealing rings, and service hardware.

Parts for Machines supplies filters across the plant, agricultural, and commercial-vehicle aftermarket. The category covers both OEM-pattern filters (matched exactly to specific equipment fitments by housing and filter dimensions) and high-quality aftermarket filters from specialist filter manufacturers.

Product pages list the filter type (engine air, oil, fuel, hydraulic, cab-air), the equipment application (the equipment make, model, and engine the filter fits), the OEM cross-reference part number, the filter dimensions (overall diameter, height, sealing-ring size), the filter rating (the smallest particle size filtered — typical 5-30 microns for hydraulic; 10-30 microns for fuel), the filter capacity (how much contamination the filter can hold before reaching pressure-drop limits), the filter media (paper, synthetic, glass-fibre, micro-glass for ultra-fine filtration), and any specific service-life specification.

For replacement of an existing filter, the OEM part number is the most reliable match. Filters have specific dimensional and filtration ratings — wrong-spec substitution gives inadequate filtration (engine wear, hydraulic-circuit contamination) or excessive flow restriction (engine starvation, hydraulic-pump damage). Always specify the OEM-equivalent filter for the equipment. Trade pricing on bulk service-pack orders is available; contact the team via WhatsApp 07754288583.

Show Only My Country Products

In this feature, you can view only your country products.

Compare

Oil Filter Spin On Full Flow, ASAS Filter- SP1064

Thread Size	1 1/8 x 16 UN
Outer Diameter	111 mm (4.37 inch)
Gasket OD	104 mm (4.09 inch)
Gasket ID	93 mm (3.66 inch)
Length	260 mm (10.24 inch)

£51.21

Outer Diameter	85 mm (3.35 inch)
Inner Diameter	13.6 mm (0.54 inch)
Inner Diameter Bottom End	13.6 mm (0.54 inch)
Length	119 mm (4.69 inch)
Overall Length	119 mm (4.69 inch)

Outer Diameter	105 mm (4.13 inch)
Inner Diameter	61 mm (2.40 inch)
Inner Diameter Bottom End	61 mm (2.40 inch)
Length	290.5 mm (11.44 inch)
Overall Length	299 mm (11.77 inch)

Outer Diameter	127 mm (5.00 inch)
Inner Diameter	64 mm (2.52 inch)
Inner Diameter Bottom Bolt Hole	9 mm (0.35 inch)
Length	286 mm (11.26 inch)
Overall Length	294 mm (11.57 inch)

Thread Size	3/4 x 16 UN
Outer Diameter	78 mm (3.07 inch)
Gasket OD	71 mm (2.80 inch)
Gasket ID	62 mm (2.44 inch)
Length	138 mm (5.43 inch)

Thread Size	1 x 14 UN
Outer Diameter	111 mm (4.37 inch)
Gasket OD	90.4 mm (3.56 inch)
Gasket ID	81.2 mm (3.20 inch)
Length	158.5 mm (6.24 inch)

Thread Size	M 24 x 1.5
Outer Diameter	106 mm (4.17 inch)
Gasket OD	80 mm (3.15 inch)
Gasket ID	71 mm (2.80 inch)
Length	123 mm (4.84 inch)

Outer Diameter	133 mm (5.24 inch)
Inner Diameter	65 mm (2.56 inch)
Inner Diameter Bottom End	65 mm (2.56 inch)
Length	286 mm (11.26 inch)
Overall Length	295.5 mm (11.63 inch)

Outer Diameter	114 mm (4.49 inch)
Inner Diameter	57 mm (2.24 inch)
Inner Diameter Bottom End	57 mm (2.24 inch)
Length	263 mm (10.35 inch)
Overall Length	268 mm (10.55 inch)

Thread Size	1 x 14 UNF
Outer Diameter	98 mm (3.86 inch)
Gasket OD	72 mm (2.84 inch)
Gasket ID	63 mm (2.48 inch)
Length	157 mm (6.18 inch)

Outer Diameter	Top End 92 mm (3.62 inch)
Outer Diameter	70 mm (2.76 inch)
Inner Diameter	62 mm (2.44 inch)
Inner Diameter Bottom Bolt Hole	17 mm (0.67 inch)
Length	305 mm (12.00 inch)

Thread Size	1 x 12 UN
Outer Diameter	111 mm (4.37 inch)
Gasket OD	71 mm (2.80 inch)
Gasket ID	62 mm (2.44 inch)
Length	228 mm (8.98 inch)

Outer Diameter	Top End Rim 68 mm (2.68 inch)
Outer Diameter	62 mm (2.44 inch)
Inner Diameter	51 mm (2.01 inch)
Inner Diameter Bolt Hole	17 mm (0.67 inch)
Length	283 mm (11.14 inch)

Outer Diameter	85 mm (3.33 inch)
Gasket OD	17 mm (0.69 inch)
Gasket ID	13 mm (0.51 inch)
Length	177 mm (6.97 inch)
Overall Length	177 mm (6.97 inch)

Outer Diameter	146 mm (5.75 inch)
Inner Diameter	84 mm (3.31 inch)
Inner Diameter Bottom End	84 mm (3.31 inch)
Length	327 mm (12.87 inch)
Overall Length	360 mm (14.17 inch)

Outer Diameter	158 mm (6.22 inch)
Inner Diameter	96 mm (3.78 inch)
Inner Diameter Bottom End	96 mm (3.78 inch)
Length	343 mm (13.50 inch)
Overall Length	376 mm (14.80 inch)

Thread Size	M 18 x 1.5
Outer Diameter	97 mm (3.82 inch)
Gasket OD	72 mm (2.83 inch)
Gasket ID	63 mm (2.48 inch)
Length	215 mm (8.46 inch)

Thread Size	1 3/8 x 16 UN
Outer Diameter	111 mm (4.37 inch)
Gasket OD	101 mm (3.98 inch)
Gasket ID	92 mm (3.62 inch)
Length	260 mm (10.24 inch)

Thread Size	M 16 x 1.5
Outer Diameter	97 mm (3.82 inch)
Gasket OD	72 mm (2.84 inch)
Gasket ID	63 mm (2.48 inch)
Length	209 mm (8.23 inch)

Outer Diameter	48.4 mm (1.91 inch)
Inner Diameter	20.5 mm (0.81 inch)
Inner Diameter Bottom End	20.5 mm (0.81 inch)
Length	87.8 mm (3.46 inch)
Overall Length	95.4 mm (3.76 inch)

Outer Diameter	Top End Rim 139 mm (5.47 inch)
Outer Diameter	127 mm (5.00 inch)
Inner Diameter	116 mm (4.57 inch)
Inner Diameter Bolt Hole	17 mm (0.67 inch)
Length	478.5 mm (18.84 inch)

find the right

Electrical Component

Shop by Sub Category

How often should I change filters on plant equipment?

OEM filter or aftermarket equivalent?

How do I match a fuel filter to my diesel engine?

Can I get matching service-pack kits with all filters for one service?

What if the part doesn't fit or arrives damaged?

How quickly will I get my order and where do you deliver?