Search
Search

Oops! We didn’t find any matching result

Main Menu
Phone Phone 01926754100 Cart Cart
Fit guarantee icon
FIT GUARANTEE or Hassle-Free Returns
Quick delivery icon
QUICK DELIVERY On All Products Across UK
Customer support icon
GREAT SUPPORT 24/7 Support For Any Query
rating icon
TOP RATED Trusted by Our Customers

Shop by Sub Category

Back to Category
  • Fuel Pumps & Fuel Injectors
FAQs

Modern common-rail injectors have a calibration code (sometimes called IMA, ISA, or correction code) printed or laser-etched on the injector body. This code identifies the injector's specific flow characteristics — small manufacturing variations between injectors are compensated by the ECU using the calibration code. When an injector is replaced, the new injector's calibration code must be programmed into the ECU using the diagnostic tool. Without the update, the ECU uses the old code, the cylinder receives slightly wrong fuel quantity, and the engine runs with cylinder-balance errors and possibly fault codes.

Solenoid injectors: traditional electromagnetic actuator with a solenoid coil and armature. Slower response (typical 0.4-0.8 ms opening time), simpler control electronics, lower cost. Used on most current common-rail engines. Piezo injectors: piezoelectric stack that physically deforms under voltage to operate the injector valve. Much faster response (0.1-0.2 ms), allows multiple injection events per cylinder cycle (pre-injection + main + post-injection), better combustion control. Used on premium and emissions-critical engines. Not interchangeable — wrong-type replacement causes injection-control failure.

Cleaning may resolve some failure modes — sticky valves caused by varnish deposits or contaminated fuel, mild spray-pattern degradation. Specialist injector cleaning services use ultrasonic baths and bench-flow testing to clean and verify injector performance. However, cleaning cannot restore mechanically-failed injectors (worn valves, damaged stack on piezo, electrical-fault solenoid). For fleet service, specialist-remanufactured injectors (cleaned, replaced wear parts, bench-calibrated) are typically more economical than full new replacement and more reliable than cleaning alone.

Yes. Replacement copper sealing washers (between the injector and the cylinder head — must be replaced when the injector is removed; reusing an old washer leaks combustion gas), seal kits (the small O-rings and back-up rings that seal the injector body and the high-pressure connection to the rail), and matching fitting kits are available across the injector range. Always replace sealing washers and back-up rings during injector service — these are wearing parts not designed for reuse. Match the washer specification to the OEM injector.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Clear

Fuel Injectors

FilterFilters
View as Grid List

Within Fuel Pumps & Fuel Injectors, Fuel Injectors covers the diesel fuel injectors fitted to plant equipment, agricultural tractors, telehandlers, and commercial-vehicle engines — covering common-rail electronic injectors (with solenoid or piezo actuators controlled by the engine ECU), pump-line-nozzle injectors (used in earlier electronic-mechanical systems), traditional mechanical injectors (used in older indirect-injection diesel engines), and the matching seal kits, sealing washers, and replacement-nozzle service parts.

Parts for Machines supplies fuel injectors across the plant, agricultural, and commercial-vehicle aftermarket — covering both OEM-pattern injectors (matched exactly to specific engine fitments) and remanufactured injectors rated for fitment to the listed engines.

Product pages list the injector type (common-rail solenoid, common-rail piezo, pump-line-nozzle, mechanical), the engine application (the engine make, model, year-range, and ECU-software version where applicable), the OEM cross-reference part number, the rated operating pressure, the spray pattern (typical 4-8 spray holes; specific pattern matters for the combustion-chamber design), the flow calibration code (where applicable for common-rail injectors — the calibration code must match what the ECU expects, or the ECU must be reprogrammed with the new code), the electrical specification (resistance for solenoid; capacitance for piezo), and any specific seal kit included.

For replacement of an existing fuel injector, the OEM part number is the most reliable match. For common-rail injectors, the calibration code is critical — most modern engines have ECU-stored calibration codes that must be updated with the new injector codes via the diagnostic tool. Without the code update, the engine runs with cylinder-balance errors. Match the engine ECU's expected calibration codes before fitment. Specialist injector-removal tools and seized-injector extractor kits are available for tight or seized fitments. Trade pricing on bulk and fleet orders is available; contact the team via WhatsApp 07754288583.

Show Only My Country Products
In this feature, you can view only your country products.
Showing 1 to 30 of 2287 entries
FAQs

Modern common-rail injectors have a calibration code (sometimes called IMA, ISA, or correction code) printed or laser-etched on the injector body. This code identifies the injector's specific flow characteristics — small manufacturing variations between injectors are compensated by the ECU using the calibration code. When an injector is replaced, the new injector's calibration code must be programmed into the ECU using the diagnostic tool. Without the update, the ECU uses the old code, the cylinder receives slightly wrong fuel quantity, and the engine runs with cylinder-balance errors and possibly fault codes.

Solenoid injectors: traditional electromagnetic actuator with a solenoid coil and armature. Slower response (typical 0.4-0.8 ms opening time), simpler control electronics, lower cost. Used on most current common-rail engines. Piezo injectors: piezoelectric stack that physically deforms under voltage to operate the injector valve. Much faster response (0.1-0.2 ms), allows multiple injection events per cylinder cycle (pre-injection + main + post-injection), better combustion control. Used on premium and emissions-critical engines. Not interchangeable — wrong-type replacement causes injection-control failure.

Cleaning may resolve some failure modes — sticky valves caused by varnish deposits or contaminated fuel, mild spray-pattern degradation. Specialist injector cleaning services use ultrasonic baths and bench-flow testing to clean and verify injector performance. However, cleaning cannot restore mechanically-failed injectors (worn valves, damaged stack on piezo, electrical-fault solenoid). For fleet service, specialist-remanufactured injectors (cleaned, replaced wear parts, bench-calibrated) are typically more economical than full new replacement and more reliable than cleaning alone.

Yes. Replacement copper sealing washers (between the injector and the cylinder head — must be replaced when the injector is removed; reusing an old washer leaks combustion gas), seal kits (the small O-rings and back-up rings that seal the injector body and the high-pressure connection to the rail), and matching fitting kits are available across the injector range. Always replace sealing washers and back-up rings during injector service — these are wearing parts not designed for reuse. Match the washer specification to the OEM injector.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Get exclusive updates on offers & latest trends in construction industry

By sharing your email, you agree to our privacy policy & terms of service