Shop by Sub Category

Rating

& up
& up
& up
& up

Hammers Breakers & Consumables

FAQs

Match the chisel profile to the work: pointed chisel — concentrated impact for breaking through hard surfaces (concrete, masonry), penetrates first then enlarges the break. Best for initial penetration and crack-starting. Flat chisel — wider impact face for chipping, prying, and removing tile or render. Best for surface-cleaning and feature-removal. Bull-point chisel — pointed but heftier than the standard pointed chisel, better impact-load resistance. Best for general demolition where impact loads are high. Spade chisel — wider pointed profile for trenching and digging. Tamper — flat compaction face for soil and aggregate compaction work.

Chisels deform under sustained high-impact loading combined with heat buildup at the chisel tip. Common deformation modes: mushrooming (the chisel-end where the hammer strikes flares outward — caused by hammer-end softening from impact heat); tip blunting (the working end loses its sharp profile through wear); shaft cracking (caused by side-load forces during levering or prying with the chisel). Prevention: rest the chisel periodically during heavy work to allow heat dissipation; avoid using the chisel for prying or levering (use it for impact only); replace the chisel when mushrooming or tip-deformation becomes visible.

Match the shank size to the hammer-breaker tool. Shank size is normally stamped on the tool body or in the equipment manual. Common shank sizes: 14mm hex (light demolition hammers — domestic and small-trade work), 17mm hex (medium hammer breakers — typical workshop and plant-service work), 19mm hex (medium-heavy hammer breakers), 22mm hex (heavy hammer breakers — full-time demolition work), SDS-Max and 28mm hex (very heavy demolition hammers). Wrong-shank chisels won't fit the tool retainer; never modify a chisel shank to fit — the impact loading will fail an improperly-fitted joint.

Yes. Replacement internal bushes (the wear-bushings around the piston and chisel guide), replacement seal kits (O-rings and sealing elements that prevent air loss in the hammer mechanism), replacement chisel retainers (the spring-loaded sleeves that hold the chisel in place during operation), and complete tool-rebuild kits (covering all wear parts for a routine service interval) are available alongside the chisel range. Match by the hammer-breaker make and model. WhatsApp 07754288583 with the tool make and model for cross-reference.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Clear

Hammer Breaker Consumables

Filters

View as

Within Hammers, Breakers & Consumables, Hammer Breaker Consumables covers the consumable parts used with pneumatic hammer-breaker tools — covering replacement chisel-and-point bits (in various shapes for different demolition and breaking applications), replacement bushes and seal kits (the wear parts inside the hammer body), replacement retainer hardware (the sleeves and pins that hold the chisel in the hammer body), and the matching accessory parts used in workshop, plant-service, and demolition applications.

Parts for Machines supplies hammer breaker consumables across the trade and industrial ranges. Chisels and points are the primary consumable for hammer breakers — wear with use, deform under high-impact loading, and require routine replacement to maintain breaking effectiveness.

We are an authorised distributor and seller of Chicago Pneumatic and SIP across the hammer breaker consumable range. Chicago Pneumatic covers production-grade chisels and points for heavy demolition and plant-service hammer breakers — hardened tool-steel chisels rated for sustained heavy-impact work. SIP covers workshop and trade-grade chisels for light to medium-duty hammer-breaker applications.

Product pages list the consumable type (chisel, point, retainer, internal wear part, seal kit), the matching hammer-breaker model (consumables are typically tool-specific by shank size — common shank sizes: 14mm hex, 17mm hex, 19mm hex, 22mm hex, plus larger SDS-Max and 28mm shanks for heavy hammer breakers), the chisel profile (flat chisel for prying and chipping; pointed for concentrated breaking; bull-point for general demolition; spade for spading work; tamper for compaction tasks), the chisel material (high-carbon tool steel for general work; hardened alloy steel for heavy demolition), the included quantity, and the warranty terms. For chisel replacement, match by the hammer-breaker shank size first (chisels are not cross-compatible between shank sizes), then by the chisel profile needed for the work. Always have spare chisels — chisel deformation can be sudden under heavy impact, and lost demolition time during chisel-change is minimised by matched-replacement readiness. Trade pricing on bulk and contractor orders is available; contact the team via WhatsApp 07754288583.

Show Only My Country Products

In this feature, you can view only your country products.