Search
Search

Oops! We didn’t find any matching result

Main Menu
Phone Phone 01926754100 Cart Cart
Fit guarantee icon
FIT GUARANTEE or Hassle-Free Returns
Quick delivery icon
QUICK DELIVERY On All Products Across UK
Customer support icon
GREAT SUPPORT 24/7 Support For Any Query
rating icon
TOP RATED Trusted by Our Customers

Shop by Sub Category

Brands

FAQs

Check the guard label or machine plate for the maximum disc diameter your grinder accepts, then confirm the spindle thread size (most UK angle grinders use M14). The bore stamped on the disc or backing pad must match that spindle, and the disc diameter must sit within the guard aperture. Ordering a disc larger than the guard allows is a safety hazard. If you have the model number to hand, use Ask Simon on the relevant product page for an instant fitment check.

Cutting discs are thin (typically 1 mm to 1.6 mm) and intended for parting cuts through bar, tube or sheet. Grinding discs are thicker (4 mm to 6 mm typically) with a depressed centre, suited to dressing welds and removing material over a wider surface. Using a cutting disc for grinding applies lateral stress it is not rated for and can cause disc fracture. Always use the disc type specified for the task at hand.

Every bonded abrasive product carries a maximum operating speed in RPM, printed or stamped on the disc face or blotter. Before fitting, compare that figure against your machine's rated no-load speed. The disc rating must equal or exceed the machine's no-load RPM. Also inspect the disc for cracks, chips or moisture damage before each use. A visually intact disc that has been dropped or stored damp should be discarded rather than fitted.

Trade quantities are available across the cutting and grinding accessories listed on PartsForMachines. If you need a mix of disc sizes, bore sizes or accessory types in a single order, contact the team directly via WhatsApp 07754288583 or [email protected] with your requirements and quantities, and they will confirm availability and put together a consolidated order for you.

Returns are accepted within 30 days of purchase, in original packaging, on orders delivered within the United Kingdom. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will typically arrange collection and replacement at no cost to you. For parts that don't fit your machine, the Fit Guarantee covers a hassle-free return at no cost. For buyer's remorse — you've changed your mind or ordered the wrong item, email us first to obtain a Return Merchandise Number; a restocking fee may apply. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and 'Check where we deliver' confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Clear

Cutting & Grinding - Additional Products

FilterFilters
View as Grid List

Cut-off wheels, grinding discs and the ancillary items that keep them running safely are the focus of this section. Whether the job is parting steel bar, dressing a weld bead or knocking back corrosion on a fabrication, the quality of the abrasive and the condition of the supporting hardware both matter. PartsForMachines lists additional cutting and grinding products here as an Authorised Distributor and Seller, filling out the consumable and accessory side of angle grinder and bench grinder work.

Selecting the right item means matching a few key variables: disc diameter and bore size to the guard and spindle on the machine, thickness for the application (thin kerf for cutting, thicker for grinding), and the material designation on the disc face. Bonded abrasive products carry ratings for maximum operating speed; fitting an item rated below the machine's no-load RPM is a safety failure, not just a performance issue, so always cross-check before fitting. Everything listed sits within the Abracs cutting and grinding additional products range.

Practical workshop habit is to treat cutting and grinding consumables as paired items. A cutting disc used past its safe diameter should come off, and a flanged backing pad or guard assembly showing wear is worth replacing at the same time. Abrasive media degrades with heat and use even when it looks intact, so periodic inspection of both the disc and the hardware holding it is part of working safely with angle grinders and bench grinders.

For sizing queries or trade quantities on cutting and grinding accessories, contact the team via WhatsApp 07754288583 or [email protected].

Show Only My Country Products
In this feature, you can view only your country products.
Showing 1 to 7 of 7 entries
FAQs

Check the guard label or machine plate for the maximum disc diameter your grinder accepts, then confirm the spindle thread size (most UK angle grinders use M14). The bore stamped on the disc or backing pad must match that spindle, and the disc diameter must sit within the guard aperture. Ordering a disc larger than the guard allows is a safety hazard. If you have the model number to hand, use Ask Simon on the relevant product page for an instant fitment check.

Cutting discs are thin (typically 1 mm to 1.6 mm) and intended for parting cuts through bar, tube or sheet. Grinding discs are thicker (4 mm to 6 mm typically) with a depressed centre, suited to dressing welds and removing material over a wider surface. Using a cutting disc for grinding applies lateral stress it is not rated for and can cause disc fracture. Always use the disc type specified for the task at hand.

Every bonded abrasive product carries a maximum operating speed in RPM, printed or stamped on the disc face or blotter. Before fitting, compare that figure against your machine's rated no-load speed. The disc rating must equal or exceed the machine's no-load RPM. Also inspect the disc for cracks, chips or moisture damage before each use. A visually intact disc that has been dropped or stored damp should be discarded rather than fitted.

Trade quantities are available across the cutting and grinding accessories listed on PartsForMachines. If you need a mix of disc sizes, bore sizes or accessory types in a single order, contact the team directly via WhatsApp 07754288583 or [email protected] with your requirements and quantities, and they will confirm availability and put together a consolidated order for you.

Returns are accepted within 30 days of purchase, in original packaging, on orders delivered within the United Kingdom. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will typically arrange collection and replacement at no cost to you. For parts that don't fit your machine, the Fit Guarantee covers a hassle-free return at no cost. For buyer's remorse — you've changed your mind or ordered the wrong item, email us first to obtain a Return Merchandise Number; a restocking fee may apply. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and 'Check where we deliver' confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Get exclusive updates on offers & latest trends in construction industry

By sharing your email, you agree to our privacy policy & terms of service