Search
Search

Oops! We didn’t find any matching result

Main Menu
Phone Phone 01926754100 Cart Cart
Fit guarantee icon
FIT GUARANTEE or Hassle-Free Returns
Quick delivery icon
QUICK DELIVERY On All Products Across UK
Customer support icon
GREAT SUPPORT 24/7 Support For Any Query
rating icon
TOP RATED Trusted by Our Customers

Shop by Sub Category

FAQs

Air angle grinders: high power-to-weight ratio, no electric-motor heat buildup (continuous operation without thermal de-rating), no electrical safety risk in wet or contaminated environments, simpler maintenance (no brushes to replace). Need an air compressor with sufficient CFM output (typical 5-15 CFM for continuous grinder use) and good air-line plumbing. Best for production fabrication, automotive, and trade workshop use. Electric angle grinders: no compressor needed, more portable for occasional use. Best for site work and where compressed-air infrastructure isn't available. Most production trade workshops use air-powered.

Match the compressor's CFM at 90psi to the grinder's rated air consumption — and add 30-50% margin for sustained use. Typical air-grinder consumption: 100mm grinder ~4-6 CFM; 125mm grinder ~6-9 CFM; 180mm grinder ~10-15 CFM. For continuous use, the compressor should deliver at least 1.5x the grinder's rated CFM. For occasional use, matching the rated CFM may be sufficient. Under-sized compressors give grinder slow-down under load and accelerated air-tool wear from low-pressure operation. The CFM rating is on every product page.

Match the disc size to the work: 75-100mm — restricted-access work, light cutting, automotive bodywork. 125mm — general workshop and fabrication, the trade workshop standard balance of capability and weight. 180mm — heavy fabrication, plant-equipment service, and structural metalwork. Larger discs cut deeper but add weight and require more compressor capacity. For most trade workshops, 125mm is the practical primary tool with smaller and larger sizes for specific tasks. The disc size capacity is on every product page.

Yes. Matched cutting discs (thin abrasive discs for cutting steel, stainless, masonry — typical 1.0-3.2mm thickness), grinding wheels (thicker abrasive wheels for material removal — typical 6-8mm thickness), wire-brush wheels (for paint removal and rust cleaning), flap discs (for finishing and light grinding), and spindle adapters (for non-standard accessory threads) are available across the air-tool accessory range. Match the accessory diameter to the grinder rating; never run an accessory rated for a smaller grinder on a larger one.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Clear

Air Angle Grinders

FilterFilters
View as Grid List

Within Compressors > Air Tools, Air Angle Grinders covers the pneumatic angle-grinder tools used in metalwork, fabrication, automotive, plant-equipment service, and the wider trade and industrial workshop applications — covering compact-body angle grinders for tight-access work, full-size body grinders for production fabrication, low-vibration variants for prolonged operator use, and the matching cutting and grinding accessories.

Parts for Machines supplies air angle grinders across the trade and industrial ranges. Air-powered angle grinders are preferred over electric in many trade applications — the high power-to-weight ratio of air motors gives sustained heavy-duty cutting and grinding performance, and the absence of electric motor heat-buildup allows continuous operation without thermal de-rating.

We are an authorised distributor and seller of SIP, Nuair, and Sealey across the air angle grinder range. SIP covers the broadest selection — full-size air angle grinders for production fabrication, compact-body variants for restricted-access work, and the matched accessory sets. Nuair extends the range with workshop and contractor variants — typically with built-in vibration-reducing features. Sealey covers trade-grade air angle grinders, with specific sizes for automotive and plant-equipment service work.

Product pages list the disc size capacity (typical 75mm, 100mm, 125mm, 180mm — the disc diameter the grinder is rated for), the rated free speed (typical 12,000-25,000 RPM at no-load — higher for smaller discs, lower for larger), the rated air consumption (in CFM at 90psi — typical 4-15 CFM depending on size), the recommended air pressure (typical 90psi/6.2 bar), the air inlet thread (typical 1/4″ BSP for small grinders; 3/8″ BSP for larger), the spindle thread (typical M10 or M14 for accessory mounting), the body weight, the noise level (in dB(A)), the vibration rating (in m/s² for hand-arm vibration assessment), and the warranty terms. Trade pricing on bulk and contractor orders is available; contact the team via WhatsApp 07754288583.

Show Only My Country Products
In this feature, you can view only your country products.
Showing 1 to 30 of 78 entries
FAQs

Air angle grinders: high power-to-weight ratio, no electric-motor heat buildup (continuous operation without thermal de-rating), no electrical safety risk in wet or contaminated environments, simpler maintenance (no brushes to replace). Need an air compressor with sufficient CFM output (typical 5-15 CFM for continuous grinder use) and good air-line plumbing. Best for production fabrication, automotive, and trade workshop use. Electric angle grinders: no compressor needed, more portable for occasional use. Best for site work and where compressed-air infrastructure isn't available. Most production trade workshops use air-powered.

Match the compressor's CFM at 90psi to the grinder's rated air consumption — and add 30-50% margin for sustained use. Typical air-grinder consumption: 100mm grinder ~4-6 CFM; 125mm grinder ~6-9 CFM; 180mm grinder ~10-15 CFM. For continuous use, the compressor should deliver at least 1.5x the grinder's rated CFM. For occasional use, matching the rated CFM may be sufficient. Under-sized compressors give grinder slow-down under load and accelerated air-tool wear from low-pressure operation. The CFM rating is on every product page.

Match the disc size to the work: 75-100mm — restricted-access work, light cutting, automotive bodywork. 125mm — general workshop and fabrication, the trade workshop standard balance of capability and weight. 180mm — heavy fabrication, plant-equipment service, and structural metalwork. Larger discs cut deeper but add weight and require more compressor capacity. For most trade workshops, 125mm is the practical primary tool with smaller and larger sizes for specific tasks. The disc size capacity is on every product page.

Yes. Matched cutting discs (thin abrasive discs for cutting steel, stainless, masonry — typical 1.0-3.2mm thickness), grinding wheels (thicker abrasive wheels for material removal — typical 6-8mm thickness), wire-brush wheels (for paint removal and rust cleaning), flap discs (for finishing and light grinding), and spindle adapters (for non-standard accessory threads) are available across the air-tool accessory range. Match the accessory diameter to the grinder rating; never run an accessory rated for a smaller grinder on a larger one.

Every product is backed by our Fit Guarantee. If a part is incompatible with your machine, you can return it hassle-free. For damaged-on-arrival items, report within 24 hours with photographs to [email protected] — we will arrange collection. For other returns, email us first to obtain a Return Merchandise Number before sending. Returns are accepted within 30 days of purchase, in original packaging, on UK orders. A restocking fee may apply on returns where the buyer has changed their mind. Refunds are issued to the original payment method once the return is inspected.

Delivery time depends on the product, your destination, and availability — the estimated time for any item appears on the product page, and "Check where we deliver" confirms coverage for your postcode before you order. Next-day delivery is available on most products; the option appears at checkout when applicable. We deliver across the UK, Europe, the Middle East, and Africa. Use the country selector at checkout to confirm coverage and delivery options for your destination.

Get exclusive updates on offers & latest trends in construction industry

By sharing your email, you agree to our privacy policy & terms of service